Showing posts with label weeping wing. Show all posts
Showing posts with label weeping wing. Show all posts

Tuesday, September 16, 2008

Icing conditions

From Wikipedia, the free encyclopedia

In aviation, icing conditions are those atmospheric conditions that can lead to the formation of water ice on the surfaces of an aircraft, or within the engine as carburetor icing. Inlet icing is another engine-related danger, often occurring in jet aircraft. These icing phenomena do not necessarily occur together. Many aircraft are not certified for flight into known icing—icing conditions which are certain to exist based on pilot reports, observations, and forecasts.

Ice forms when air containing water vapour is cooled below the freezing point of water, which becomes higher with decreasing pressure; ice is likely to form wherever there is reduced pressure, including wings and empennage (where it is known as structural icing), carburetors, pitot tubes, and engine inlets. Ice gradually builds as long as icing conditions exist and if left unchecked results in dangerous conditions. Ice adds to an aircraft's weight and disrupts airflow, increasing the stall speed. In engines, carburetor ice and inlet ice can lead to reduced power or complete engine failure.

Types of structural ice

  • Glaze ice is often clear and smooth. Supercooled water droplets, or freezing rain, strike a surface but do not freeze instantly. Often "horns" or protrusions are formed and project into the airflow.
  • Rime ice is rough and opaque, formed by supercooled drops rapidly freezing on impact. Forming mostly along an airfoil's stagnation point, it generally conforms to the shape of the airfoil.
  • Mixed ice is a combination of clear and rime ice.
  • Runback ice is the result of water freezing on unprotected surfaces. Often forming behind deicing boots or heated leading edges, it was a factor in the crash of American Eagle Flight 4184.

Icing prevention and removal

Several methods exist to reduce the dangers of icing. The first, and simplest, is to avoid icing conditions altogether, but for many flights this is not practical.

If icing is expected, deicing fluid can be applied to the aircraft before flight to prevent ice from forming, or from sticking to the surface if it does form. Airliners are often deiced before departure, and the deicing fluid prevents ice buildup for a short time after.

Another common approach is to include heating elements along the leading edges of wings and tailplanes, which can keep the surface temperature above freezing point. A weeping wing has hundreds of small holes in the leading edges and releases deicing fluid on demand to clear the entire wing of ice. Older aircraft and propellers are often equipped with pneumatic deicing boots

Carburetor heat is applied to carbureted engines to prevent and clear icing. Fuel-injected engines are not susceptible to carburetor icing but can suffer from blocked inlets. In these engines an alternate air source is often available.

Note there is a difference between deicing and anti-icing.

See also

Ice protection system

From Wikipedia, the free encyclopedia

Ice protection systems are designed to keep atmospheric ice from accumulating on aircraft flight surfaces while in flight. The effects of ice accretion on an aircraft can cause loss of control, resulting in a catastrophic flight event.

Types of ice protection systems

The pneumatic boot is a rubber device attached to a wing's leading edge, invented by the Goodrich Corporation (previously known as B.F. Goodrich) in 1923. Portions of the boot are inflated to break ice off the boot, de-icing the wing. Rubber boots are used on jets and propeller driven aircraft.

A bleed air system is used by jet aircraft to keep flight surfaces above the freezing temperature required for ice to accumulate (called anti-icing). The hot air is "bled" off the jet engine into tubes routed through wings, tail surfaces, and engine inlets.

Electrical thermal systems use electricity to heat the protected surface. The electric heaters are usually flexible enough to use as anti-icers or de-icers. As a de-icer, the heater melts the ice, the ice no longer sticks to the surface due to aerodynamic forces. As an anti-icer, the heater keeps the surface to the point that the ice does not form.

Electro-mechanical systems use a mechanical force to knock the ice off the flight surface. Typically, actuators are installed underneath the skin of the structure. The actuator is moved to induce a shock wave in the protected surface to dislodge the ice.

A weeping wing system uses a liquid (such as ethylene glycol) to coat the surface and prevent ice from accumulating.

Wing and Flight Surfaces

Ice accumulates on the leading edge of wings, tails, and horizonal stabilizers as an aircraft flies through a cloud containing super-cooled water droplets. Ice forms because super-cooled water droplets in clouds contact the aircraft. This contact imparts energy into the droplet and causes it to change from liquid water to solid water (ice). As the ice layer grows (accretes), it affects the airflow over the affected surface. If the layer grows large enough, it can create lift or handling problems for the aircraft.

Rotary Surfaces

Ice can also accumulate on helicopter rotor blades and aircraft propellers. The accretion causes weight and aerodynamic imbalances that are amplified due to the rapid rotation of the propeller or rotor.

Engine Inlets

Ice accreting on the leading edge (lip) of engine inlets causes flow problems and can lead to ice ingestion. In turbofan engines, laminar airflow is required at the face of the fan. Because of this, most engine ice protection systems are anti-ice systems (prevent build up).

Related Companies

Related accidents