Showing posts with label instrument approach. Show all posts
Showing posts with label instrument approach. Show all posts

Friday, November 7, 2008

Instrument approach

From Wikipedia, the free encyclopedia
Terminal procedures for an ILS approach in the United States. (The disclaimers shown in red in the illustration do not appear on the original approach plate.)

An instrument approach or instrument approach procedure (IAP) is a type of air navigation that allows pilots to land an aircraft in reduced visibility (known as instrument meteorological conditions or IMC), or to reach visual conditions permitting a visual landing.

Approaches are classified as either precision or nonprecision, depending on the accuracy and capabilities of the navigational aids (navaids) used. Precision approaches utilize both lateral (localizer) and vertical (glideslope) information. Nonprecision approaches provide lateral course information only.

The publications depicting instrument approach procedures are called Terminal Procedures, but are commonly referred to by pilots as "approach plates". These documents graphically depict the specific procedure to be followed by a pilot for a particular type of approach to a given runway. They depict prescribed altitudes and headings to be flown, as well as obstacles, terrain, and potentially conflicting airspace. In addition, they also list missed approach procedures and commonly-used radio frequencies.

Basic principles

Instrument approaches are generally designed such that a pilot of an aircraft in instrument meteorological conditions (IMC), by the means of radio, GPS or INS navigation with no assistance from air traffic control, can navigate to the airport, hold in the vicinity of the airport if required, then fly to a position from where he or she can obtain sufficient visual reference of the runway for a safe landing to be made, or execute a missed approach if the visibility is below the minimums required to execute a safe landing. The whole of the approach is defined and published in this way so that aircraft can land if they suffer from radio failure; it also allows instrument approaches to be made procedurally at airports where air traffic control does not use radar or in the case of radar failure.

Instrument approaches generally involve five phases of flight:

  • Arrival: where the pilot navigates to the Initial Approach Fix (IAF: a navaid or reporting point), and where holding can take place.
  • Initial Approach: the phase of flight after the IAF, where the pilot commences the navigation of the aircraft to the Final Approach Fix (FAF), a position aligned with the runway, from where a safe controlled descent back towards the airport can be initiated.
  • Intermediate Approach: an additional phase in more complex approaches that may be required to navigate to the FAF.
  • Final approach: between 4 and 12 nms of straight flight descending at a set rate (usually an angle of between 2.5 and 6 degrees).
  • Missed Approach: an optional phase; should the required visual reference for landing not have been obtained at the end of the final approach, this allows the pilot to climb the aircraft to a safe altitude and navigate to a position to hold for weather improvement or from where another approach can be commenced.

When aircraft are under radar control, air traffic controllers may replace some or all of these phases of the approach with radar vectors (the provision of headings on which the controller expects the pilot to navigate his aircraft) to the final approach, to allow traffic levels to be increased over those of which a fully procedural approach is capable. It is very common for air traffic controllers to vector aircraft to the final approach aid, e.g. the ILS, which is then used for the final approach. In the case of the rarely-used Ground-Controlled Approach (GCA), the instrumentation (normally Precision Approach Radar) is on the ground and monitored by a controller, who then relays precise instructions for adjustment of heading and altitude to the pilot in the approaching aircraft.

Low visibility approaches

Many instrument approaches allow for landing in conditions of low visibility. ICAO classifies ILS approaches as being in one of the following categories:

ILS Categories
Category Decision Height (above threshold) RVR limit
I greater than 200 ft 550m or 1800 ft
II less than 200 ft 350m or 1200 ft
IIIa less than 100 ft 150m - 200m (see below)
IIIb less than 50 ft 75m - 150m (see below)
IIIc No DH No RVR

Cat III mimima depend on Roll Out Control & Redundancy of the Autopilot.

Low visibility approaches are those in categories II and III.

For larger aircraft it is typical that these approaches are under the control of the flight control system with the flight crew providing a supervisory role.

Traditionally smaller aircraft which lacked redundancy in the flight control systems could not fly these approaches. (Imagine a radio getting a glitch at the moment of flare which causes the airplane to "think" that a large correction is required. The result would, most likely, be a sudden turn which at low altitude would be catastrophic.) A Head-Up Display allows the flight crew to fly the aircraft using the guidance cues from the ILS sensors so that if such a large deviation were seen, the pilot would be able to respond in an appropriate and safe manner. This is becoming increasingly popular with "feeder" airlines and most manufactures of regional jets are now offering HUDs as either standard or optional equipment. In addition a HUD can provide a low visibility take off capability.

For both automatic and HUD landing systems, the equipment requires special approval for its design and also for each individual installation. The design takes into consideration all of the additional safety requirements for operating an aircraft in close proximity to the ground and takes into consideration the ability of the flight crew to react to a "system anomaly." Once installed, the equipment also has additional maintenance requirements to ensure that it is fully capable of supporting reduced visibility operations.

In all cases, additional crew training is required for such approaches, and a certain number of low visibility approaches must either be performed or simulated in a set period of time for pilots to stay 'current' in performing them.

For practical reasons Category IIIc approaches are rare, but category IIIb approaches are relatively common at major airports.

There are also air traffic control considerations with low visibility approaches: when using ILS, the integrity of the signal must be protected, which requires that certain areas of the airport close to the installations being free of other aircraft and vehicles. Also there must be bigger gaps between aircraft on final approach to both protect the ILS signal and to cope with slower runway vacation times. In addition, the airport itself has special considerations for low visibility operations including different lighting for approach, runways, and taxiways as well as the location of emergency equipment.

Precision approaches and systems

  • ILS - Instrument Landing System
  • MLS - Microwave Landing System
  • PAR - Precision Approach Radar (Military)
  • GPS (with vertical navigation via WAAS or EGNOS) - Global Positioning System
  • LAAS - Ground Based Augmentation System (GBAS) for Global Satellite Navigation Systems (GNSS)
  • JPALS - Joint Precision Approach and Landing System
  • GCA - Ground-Controlled Approach (mostly military)

Nonprecision approaches and systems

Terminology

Decision Height or Altitude

A decision height (DH) or decision altitude (DA) is a specified height or altitude in the precision approach at which a missed approach must be initiated if the required visual reference to continue the approach has not been acquired. This allows the pilot sufficient time to safely re-configure the aircraft to climb and execute the missed approach procedures while avoiding terrain and obstacles.

Minimum Descent Height or Altitude

A minimum descent height (MDH) or minimum descent altitude (MDA) is the equivalent of the DA for non-precision approaches, however there are some significant differences. It is the level below which a pilot making such an approach must not allow his or her aircraft to descend unless the required visual reference to continue the approach has been established. Unlike a DA, a missed approach need not be initiated once the aircraft has descended to the MDH, that decision can be deferred to the missed approach point (MAP). So a pilot flying a non-precision approach may descend to the minimum descent altitude and maintain it until reaching the MAP, then initiate a missed approach if the required visual reference was not obtained. An aircraft must not descend below the MDH until visual reference is obtained, which differs from a DH in that an aircraft may descend below DH without visual reference so long as the missed approach procedure was initiated at or prior to the DH. For example, with a DH of 500ft AMSL, it is legal for a pilot to allow the aircraft to descend to 450ft AMSL if the missed approach procedure was initiated at or prior to 500ft. This would not be legal during a non-precision approach with a MDH of 500ft. This difference is due to the presence of vertical guidance during a precision approach, and thus terrain clearance near DH being less of an issue than near MDH during a non-precision approach.

If a runway has both precision and non-precision approaches defined, the MDA of the non-precision approach is almost always greater than the DA of the precision approach, due to the lack of vertical guidance of the non-precision approach: the actual difference will also depend on the accuracy of the navaid upon which the approach is based, with ADF approaches and SRAs tending to have the highest MDAs.

Straight-in Approach

A straight in instrument approach is one where the final approach is begun without first having executed a procedure turn, not necessarily completed with a straight-in landing or made to straight-in landing minimums.

Circling To Land

A circle to land maneuver is a maneuver used when a runway is not aligned to within 30 degrees of the track of the instrument approach procedure or the final approach requires 400 feet of descent (or more) per nautical mile, and therefore requires some visual maneuvering of the aircraft in the vicinity of the airport after the instrument portion of the approach is completed for the aircraft to become aligned with the runway to land.

It's very common for a circle to land maneuver be executed during a straight-in approach to a different runway, e.g. an ILS approach to one runway, followed by a low-altitude pattern flying, ending in a landing on a different runway. This way, approach procedures to one runway can be used to land on any runway at the airport, as the other runways may lack instrument procedures or their approaches cannot be used for other reasons (traffic considerations, navigation aids being out of service, etc).

Circling to land is considered more difficult and less safe than a straight-in landing, especially under Instrument meteorological conditions.

Instrument Currency

In some countries Instrument Rated Pilots are required to perform a minimum number of instrument approaches in a set period to remain current. Pilots may also have to fly a certain number of low visibility approaches (Cat 2 or Cat 3) to remain current at performing these. When practicing instrument approaches in visual meteorological conditions, a safety pilot is required. This is because the pilot practicing instrument approach must wear a view limiting device, which restricts his field of view to the instrument panel. A safety pilot's basic role is to observe and help to avoid traffic.

Airport Requirements

The requirements for an airport to offer instrument approaches is contained in FAA Order 8200.97 AIRMAN AND AIRCRAFT APPROVAL FOR REDUCED VISIBILITY FLIGHT OPERATIONS, INCLUDING CATEGORY II/III OPERATIONS.

References

Audio and Multimedia Resources

Wednesday, July 16, 2008

Instrument Flight rules (IRF)

From Wikipedia, the free encyclopedia

Instrument flight rules (IFR) are a set of regulations and procedures for flying aircraft whereby navigation and obstacle clearance is maintained with reference to aircraft instruments only, while separation from other aircraft is provided by Air Traffic Control. In layman's terms, a pilot who is rated for IFR can keep a plane in controlled flight solely on the data provided by his instruments, even if that pilot cannot see anything (useful) out the cockpit windows; indeed, one of the benefits of these regulations is the ability to fly through clouds, which is otherwise not allowed.
IFR is an alternative to visual flight rules (VFR), where the pilot is ultimately responsible for navigation, obstacle clearance and traffic separation using the see-and-avoid concept. The vast majority of commercial traffic (any flight for hire) and all scheduled air carriers operate exclusively under IFR. Commercial aircraft providing sight seeing flights, aerial photography, or lift services for parachute jumping usually operate under VFR.

Separation

This article or section deals primarily with the United States and does not represent a worldwide view of the subject.Please improve this article or discuss the issue on the talk page.
The distance by which an aircraft avoids obstacles or other aircraft is termed separation. The most important concept of IFR flying is that separation is maintained regardless of meteorological visibility conditions. In controlled airspace, Air Traffic Control (ATC) separates IFR aircraft from obstacles and other IFR and known VFR aircraft by applying a flight clearance based on route, time, distance, speed, and altitude differences between aircraft. ATC monitors IFR flights by relying either on radar or aircraft position reports. Aircraft position reports are traditionally sent as voice radio transmissions, but increasingly also as electronic data exchanges. Aircraft position reports are not necessary if ATC has an aircraft in radar contact. In the United States a flight operating under IFR is required to fall back to position reports if advised radar contact lost.
IFR flights require an ATC clearance for each part of the flight. A clearance always specifies a clearance limit, which is the farthest the aircraft can fly without a new clearance. In addition, a clearance typically provides a heading or route to follow, altitude, and communication parameters, such as frequencies and transponder codes. An aircraft operating VFR must also obtain a clearance to enter class B and class C airspace, and is required to maintain an assigned heading or altitude restriction as long as it does not conflict with the safe operation of the aircraft.
In uncontrolled airspace, IFR aircraft do not require clearances, and they separate themselves from each other by using charted minimum altitudes to avoid terrain and obstacles, standard cruising altitudes to avoid aircraft flying in different directions, and radio reports over mandatory locations.
In the United States and the Southern Domestic Airspace of Canada (SDA), airspace from 18,000 to 60,000 feet (5,586 to 18,288 meters) is designated as class A, requiring an IFR clearance for all aircraft. In other countries class A airspace begins higher or lower. For example, in France class A airspace begins at 19,500 feet (5,850 meters).
In the United States even when on a filed IFR flight plan, if conditions permit the pilot is responsible to maintain a watch for, and avoid other air traffic and obstructions. Separation may also be referred to as 'protection'.

Weather
The main purpose of IFR is the safe operation of aircraft in Instrument Meteorological Conditions (IMC). The weather is considered to be IMC when it does not meet the minimum requirements for Visual Meteorological Conditions. To operate safely in IMC , a pilot controls the aircraft relying on flight instruments, and ATC provides separation.


VMC Flying under IFR
It is important to not to confuse IFR with IMC. The vast majority of IFR flying is conducted in Visual Meteorological Conditions (VMC). Any time a flight is operating in VMC, the crew is responsible for seeing and avoiding other traffic, however, since the flight is conducted under Instrument Flight Rules, ATC still provides separation services.
During flight under IFR, there are no visibility requirements, and as such flying through clouds is permitted. There are still minimum conditions that must be present in order for the aircraft to take off and land; these will vary according to the type of navigation aids available, the location and height of terrain and obstructions in the vicinity of the airport, equipment on the aircraft, and according to qualifications of the crew. For example, landing at mountain airports such as Reno (KRNO) offer significantly different instrument approaches for aircraft landing on the same runway, but from opposite directions. Aircraft approaching from the north must make visual contact with the airport at a higher altitude than a flight approaching from the south, because of rapidly rising terrain south of the airport. This higher altitude allows a flight crew to start a climb earlier in case landing is not feasible.
Although large airliners and, increasingly, smaller aircraft now carry their own terrain- and collision-avoidance systems such as TCAS, these are primarily backup systems providing a last layer of defense if a sequence of errors or omissions causes a dangerous situation.

Navigation
Under IFR, the primary means of navigation are either via radio beacons on the ground, such as VORs and NDBs, or GPS. In areas of radar coverage, ATC may also assign headings to IFR aircraft, also known as radar vectors. Radar vectors are the primary method for ATC to provide separation between aircraft for landing.
Modern Flight Management Systems have evolved sufficiently to allow a crew to plan a flight not only as to route and altitude, but to specific time of arrival at specific locations. This capability is used in several trial projects experimenting with four dimensional approach clearances for commercial aircraft, with time as the fourth dimension. These clearances allow ATC to optimize the arrival of aircraft at major airports, which increases airport capacity, and uses less fuel providing monetary and environmental benefits to airlines and the public at large respectively.
Required Navigation Performance (RNP)
ADS-B

Procedures
Main article: flight procedure
There are three stages to an IFR flight: departure, en route, and approach. For each stage there are standard, published procedures to allow IFR aircraft to move in a safe, orderly way, from the moment the wheels leave the runway to the moment they touch down again. These procedures also allow an IFR aircraft to complete a flight predictably in case of communication failure (lost-comm) with ATC, with default altitudes and headings for every stage. , and any modifications to the route. Here is an example of an IFR clearance, for a Cessna aircraft traveling from Palo Alto airport (KPAO) to Stockton airport (KSCK).
"Cessna 6253G is cleared to Stockton Airport. After departure, turn right heading zero-six-zero within one mile of the airport. Radar Vectors San Jose, Victor-334, SUNOL, Victor-195, Manteca, direct. Climb and maintain 3,000 expect 5,000 five minutes after departure. Departure frequency is 121.3, squawk 4263." Note: Not to be used for Real World Navigation
Detailed explanation:
"Cessna 6253G"
Verifies that only this specific aircraft is cleared.
"is cleared to Stockton Airport."
Clearance Limit: the farthest destination the aircraft is allowed to go under IMC (in most cases it is the destination airport).
"After departure, turn right heading zero-six-zero within one mile of the airport."
The pilot is expected to execute the turn to 060° without further ATC prompting within one mile of the departure airport.
"Radar Vectors San Jose"
The departure controller will provide directional guidance to the San Jose VOR.
"Victor-334, SUNOL, Victor-195, Manteca, direct."
After arriving at the San Jose VOR, the pilot will likely resume navigation without ATC prompts along the described airways and intersection to the Manteca VOR and then direct to the destination airport.
"Climb and maintain 3,000 ..."
After takeoff, climb to an altitude of 3000 feet above sea level.
"... expect 5,000 five minutes after departure."
Your final altitude assignment is probably going to be 5000 feet above sea level. However, you must follow actual ATC altitude assignments throughout the flight. This portion of the clearance provides a backup if communications are lost, allowing you to proceed to climb and maintain 5000 feet.
"Departure frequency is 121.3, ..."
Contact with NORCAL Departure on the specified communication frequency, after Palo Alto Tower tells you to switch.
"... squawk 4263."
Program your transponder to 4263 so that ATC can positively identify you on radar.
Departures are described in an IFR clearance issued by ATC prior to takeoff. The departure clearance may contain an assigned heading, one or more waypoints, and an initial altitude to fly. The clearance can also specify a departure procedure (DP), or standard instrument departure (SID) that should be followed unless "NO DP" is specified in the notes section of the filed flight plan.
En route flight is described by IFR charts showing navigation aids, fixes, and standard routes called airways. Aircraft with appropriate navigational equipment such as GPS, are also often cleared for a direct-to routing, where only the destination, or a few navigational waypoints are used to describe the route that the flight will follow. ATC will assign altitudes in its initial clearance or amendments thereto, and navigational charts indicate minimum safe altitudes for airways.
The approach portion of an IFR flight may begin with a Standard Terminal Arrival Route (STAR), describing common routes to fly to arrive at an initial approach fix (IAF) from which an instrument approach commences. Instrument approaches are categorized as precision and non-precision. Despite the names, a precision approach simply indicates that vertical guidance (as well as lateral guidance) is being used. non-precision indicates only lateral guidance.
In either case, an instrument approach will terminate either in visual conditions sufficient for a normal landing of the airplane, or in a missed approach if such conditions are not encountered in time. The point at which the crew of an aircraft has to make a decision to either proceed visually, or "miss" the approach is called either the Decision Altitude (DA) or Decision Height (DH) for precision approaches, and missed approach point (MAP) for non-precision approaches. During precision approaches the altitude of the aircraft is determined by the navigational instruments. For non-precision approaches the crew will descend to specific altitudes during the approach procedure, with the final altitude termed the Minimum Descent Altitude (MDA).
Some commercial aircraft are equipped with automatic landing systems that allow the aircraft to land without transitioning from instruments to visual conditions for a normal landing. Such Autoland operations require specialized equipment, procedures and training, and involve the aircraft, airport, and the crew. Autoland is the only way some major airports such as Paris CDG remain operational every day of the year. Some modern aircraft are equipped with enhanced vision systems based on infrared sensors, that provide a day-like visual environment and allow operations in conditions and at airports that would otherwise not be suitable for a landing. Commercial aircraft also frequently use such equipment for takeoffs when takeoff minimums are not met.[1]
Documents describing the approach procedure are also frequently called approach plates in reference to the plate-like appearance of single-page sheet that it is printed on.
An instrument approach that terminates in a missed approach will continue using missed approach procedure information shown on the approach procedure. Typically it describes a transition to a nearby navigational fix, from which the instrument approach can be attempted again. In practice an approach that terminates in a missed approach rarely flies the missed approach procedure as published. Instead, ATC will assign headings and altitudes that will weave the aircraft into the arriving traffic for a repeated approach attempt. The crew may also request an alternate destination, either a previously stated alternate airport, or other suitable airport considering the prevailing weather conditions.

Qualifications
To fly under IFR, a pilot must have an instrument rating, and must meet currency of experience requirements. In the United States, these currency of experience requirements include six instrument approaches, NAVAID intercepting and tracking, and holding procedures in the past six months. The aircraft must also be equipped and type-certified for instrument flight, and the related navigational equipment must have been inspected within a specific period of time prior to the instrument flight.
The UK differs from pilot licensing practice in the U.S. In the UK any pilot can decide to which flight rules he adheres given that the meteorological conditions for those rules are met. The pilot does need an instrument rating to fly in instrument meteorological conditions, and under IFR in controlled airspace. The upshot of this is that non-instrument qualified pilots can elect to fly under IFR in visual meteorological conditions outside controlled airspace. Compared to the rest of the world the UK's flight crew licensing regime is somewhat unusual in this respect by licensing for meteorological conditions and airspace, rather than flight rules. As a partial alternative to the instrument rating, the UK issues an "IMC rating", the privileges of which include flight under IFR in controlled (classes D and E) airspace and flight outside controlled airspace in instrument meteorological conditions.

References
^ For example, Southwest Airlines flies Head Up Display (HUD) equipped Boeing 737 aircraft to fog-prone airports such as Sacramento International (KSMF), allowing flights to take off when they would otherwise be unable to do so.

External links
(English) FAA website
(English) Hear audio of a US instrument rating checkride - Part 1
(French) (English) ORBIFLY : FAA School in Europe, specialized in CPL & IFR trainings
(French) (English) Free newsletter, by Orbifly, for FAA Pilots (French and English)

See also
Instrument Flying Handbook (FAA-H-8083-15A)
Instrument Procedures Handbook (FAA-H-8261-1A)
Flight instruments
Visual flight rules (VFR)
Special visual flight rules (SVFR)
VHF Omni-directional Range (VOR)
Instrument Landing System (ILS)
Non-Directional Beacon (NDB)
Distance Measuring Equipment (DME)
Global Positioning System (GPS)
Airspace classes
Helmet fire in student pilots
Autoland
Bárány chair
Approach plate

Retrieved from "http://en.wikipedia.org/wiki/Instrument_flight_rules"
Categories: Aviation terminology Airport terminology

Hidden categories: All articles with unsourced statements Articles with unsourced statements since June 2008 Articles with limited geographic scope USA-centric


All text is available under the terms of the GNU Free Documentation License. (See Copyrights for details.) Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a U.S. registered 501(c)(3) tax-deductible nonprofit charity.
Privacy policy
About Wikipedia
Disclaimers