Showing posts with label airspeed indicator. Show all posts
Showing posts with label airspeed indicator. Show all posts

Wednesday, September 10, 2008

Pitot-static system

From Wikipedia, the free encyclopedia

A pitot-static system is a system of pressure-sensitive instruments that is most often used in aviation to determine an aircraft's airspeed, Mach number, altitude, and altitude trend. A pitot-static system generally consists of a pitot tube, a static port, and the pitot-static instruments.[1] This equipment is used to measure the forces acting on a vehicle as a function of the temperature, density, pressure and viscosity of the fluid in which it is operating.[2] Other instruments that might be connected are air data computers, flight data recorders, altitude encoders, cabin pressurization controllers, and various airspeed switches. Errors in pitot-static system readings can be extremely dangerous as the information obtained from the pitot static system, such as altitude, is often critical to a successful flight. Several commercial airline disasters have been traced to a failure of the pitot-static system.[3]

Diagram of a pitot-static system including the pitot tube, pitot-static instruments and static port
Diagram of a pitot-static system including the pitot tube, pitot-static instruments and static port

Pitot-static pressure

Examples of pitot tube, static tube, and pitot-static tube.
Examples of pitot tube, static tube, and pitot-static tube.

The pitot-static system of instruments works by measuring pressures or pressure differences to give an indication of speed and altitude.[1] These pressures can come either from the static port (static pressure) or the pitot tube (pitot pressure). The static pressure is used in all measurements, while the pitot pressure is only used to determine airspeed.

Pitot pressure

The pitot pressure is obtained from the pitot tube. The pitot pressure is a measure of the ram air pressure (the dynamic air pressure created by vehicle motion), which, under ideal conditions, is equal to stagnation pressure. The pitot tube is most often located on the wing or front section of an aircraft, facing forward, where its opening is exposed to the relative wind.[1] By situating the pitot tube in such a location, the ram air pressure is more accurately measured since it will be less distorted by the aircraft's structure. When airspeed is increased, the ram air pressure is increased, which can be translated by the airspeed indicator.[1]


Static pressure

The static pressure is obtained through a static port. The static port is most often a flush-mounted hole on the fuselage of an aircraft, and is located where it can access the air flow in a relatively undisturbed area.[1] Some aircraft may have a single static port, while others may have more than one. In situations where an aircraft has more than one static port, there is usually one located on each side of the fuselage. With this positioning, an average pressure can be taken, which allows for more accurate readings in specific flight situations.[1] An alternative static port may be located inside the cabin of the aircraft as a backup for when the external static port(s) are blocked. A pitot-static tube effectively integrates the static ports into the pitot probe. It incorporates a second coaxial tube (or tubes) with pressure sampling holes on the sides of the probe, outside the direct airflow, to measure the static pressure.

Multiple pressure

Typical hemispherical multi-hole air data probe design.
Typical hemispherical multi-hole air data probe design.
Representative multi-hole air data probe coordinate system (source: NASA Technical Memorandum 4047).
Representative multi-hole air data probe coordinate system (source: NASA Technical Memorandum 4047).
Schematic and port numbering of a conical 5-hole air data probe.
Schematic and port numbering of a conical 5-hole air data probe.

Some pitot-static systems incorporate single probes that contain multiple pressure-transmitting ports that allow for the sensing of pitot. static, angle of attack, and angle of sideslip data. Depending on the design, such air data probes may be referred to as 5-hole or 7-hole air data probes. Differential pressure sensing techniques can used to produce angle of attack and angle of sideslip indications.

Pitot-static instruments

Airspeed indicator diagram showing pressure sources from both the pitot tube and static port
Airspeed indicator diagram showing pressure sources from both the pitot tube and static port

The pitot-static system obtains pressures for interpretations by the pitot-static instruments. While the explanations below explain traditional, mechanical instruments, many modern aircraft use air data computers (ADC) to calculate airspeed, rate of climb, altitude and mach number. Two ADCs receive total and static pressure from independent pitot tubes and static ports, and the aircraft's flight data computer compares the information from both computers and checks one against the other. There are also "standby instruments", which are back-up pneumatic instruments employed in the case of problems with the primary instruments.

Airspeed indicator

Main article: Airspeed indicator

The airspeed indicator is the only instrument that uses the ram pressure from the pitot tube. The airspeed indicator is connected to both the ram and static pressure sources. The greater the difference between the ram pressure and the static pressure, the higher the airspeed reported.[4] A traditional mechanical airspeed indicator contains a pressure diaphragm that is connected to the pitot tube. The case around the diaphragm is airtight and is vented to the static port. The higher the speed, the higher the ram pressure, the more pressure exerted on the diaphragm, and the larger the needle movement through the mechanical linkage.[4]

Diagram of an altimeter
Diagram of an altimeter

Altimeter

Main article: Altimeter

The pressure altimeter, also known as the barometric altimeter, is used to determine changes in air pressure that occur as the aircraft's altitude changes.[4] Pressure altimeters must be calibrated prior to flight to register the pressure as an altitude above sea level. The instrument case of the altimeter is airtight and has a vent to the static port. Inside the instrument, there is a sealed aneroid barometer. As pressure in the case decreases, the internal barometer expands, which is mechanically translated into a determination of altitude. The reverse is true when descending from higher to lower altitudes.[4]

Machmeter

Main article: Machmeter

Aircraft designed to operate at transonic or supersonic speeds will incorporate a machmeter. The machmeter is used to show the ratio of true airspeed in relation to the speed of sound. Most supersonic aircraft are limited as to the maximum Mach number they can fly, which is known as the "Mach limit". The Mach number is displayed on a machmeter as a decimal fraction.[4]

A vertical airspeed indicator
A vertical airspeed indicator

Vertical airspeed indicator

Main article: Variometer

The variometer, also known as the vertical speed indicator (VSI) or the vertical velocity indicator (VVI), is the pitot-static instrument used to determine whether an aircraft is flying in level flight.[5] The vertical airspeed specifically shows the rate of climb or the rate of descent, which is measured in feet per minute or meters per second.[5] The vertical airspeed is measured through a mechanical linkage to a diaphragm located within the instrument. The area surrounding the diaphragm is vented to the static port through a calibrated leak (which also may be known as a "restricted diffuser").[4] When the aircraft begins to increase altitude, the diaphragm will begin to contract at a rate faster than that of the calibrated leak, causing the needle to show a positive vertical speed. The reverse of this situation is true when an aircraft is descending.[4] The calibrated leak varies from model to model, but the average time for the diaphragm to equalize pressure is between 6 and 9 seconds.[4]

Pitot-static errors

There are several situations that can affect the accuracy of the pitot-static instruments. Some of these involve failures of the pitot-static system itself—which may be classified as "system malfunctions"—while others are the result of faulty instrument placement or other environmental factors—which may be classified as "inherent errors".[6]

System malfunctions

Blocked pitot tube

A blocked pitot tube is a pitot-static problem that will only affect airspeed indicators.[6] A blocked pitot tube will cause the airspeed indicator to register an increase in airspeed when the aircraft climbs from lower to higher altitudes. In reverse, the airspeed indicator will show a decrease in airspeed when the aircraft descends to lower altitudes. The pitot tube's location, near the leading edge of the wings, leaves it susceptible to becoming clogged by an obstruction or through icing.[6] For this reason, aviation regulatory agencies such as the U.S. Federal Aviation Administration (FAA) recommend that the pitot tube be checked for obstructions prior to any flight.[5] To prevent icing many pitot tubes are equipped with a heating element, and in aircraft certified for instrument flight a heated pitot tube is required.[6]

Blocked static port

A blocked static port is a more serious situation because it affects all pitot-static instruments.[6] One of the most common causes of a blocked static port is airframe icing. A blocked static port will cause the altimeter to freeze at a constant value, the altitude at which the static port became blocked. The vertical speed indicator will become frozen at zero and will not change at all, even if vertical airspeed increases or decreases. The airspeed indicator will reverse the error that occurs with a clogged pitot tube and cause the airspeed be read less than it actually is as the aircraft climbs. When the aircraft is descending, the airspeed will be over-reported. In most aircraft with unpressurized cabins, an alternative static source is available and can be toggled from within the cockpit of the airplane.[6]

Inherent errors

Inherent errors may fall into several categories, each affecting different instruments. Density errors affect instruments reporting airspeed and altitude. This type of error is caused by variations of pressure and temperature in the atmosphere. A compressibility error occurs when the air entering the pitot tube becomes less able to resist compression. At higher altitudes, the air is less dense and therefore more easily compressed; likewise, the aircraft's forward motion itself compresses the air around the aircraft. Such conditions become significant at altitudes above 10,000 feet (3,000 m) and at airspeeds greater than 200 knots (370 km/h). This error affects the airspeed indicator and causes a reading that is higher than the actual airspeed.[6] Hysteresis is an error that is caused by mechanical properties of the aneroid capsules located within the instruments. These capsules, used to determine pressure differences, have physical properties that resist change by retaining a given shape, even though the external forces may have changed. Reversal errors are caused by a false static pressure reading. This false reading may be caused by abnormally large changes in an aircraft's pitch. A large change in pitch will cause a momentary showing of movement in the opposite direction. Reversal errors primarily affect altimeters and vertical speed indicators.[6]

Position errors

Another class of inherent errors is that of position error. A position error is produced by the aircraft's static pressure being different from the air pressure remote from the aircraft. This error is caused by the air flowing past the static port at a speed different from the aircraft's true airspeed. Position errors may provide positive or negative errors, depending on one of several factors. These factors include airspeed, angle of attack, aircraft weight, acceleration, aircraft configuration, and in the case of helicopters, rotor downwash.[6] There are two categories of position errors, which are "fixed errors" and "variable errors". Fixed errors are defined as errors which are specific to a particular make of aircraft. Variable errors are caused by external factors such as deformed panels obstructing the flow of air, or particular situations which may overstress the aircraft.[6]

Pitot-static related disasters

References

  1. ^ a b c d e f [1997] (2004) in Willits, Pat: Guided Flight Discovery - Private Pilot, Abbot, Mike Kailey, Liz, Jeppesen Sanderson, Inc., 2-48 - 2-53. ISBN 0-88487-333-1.
  2. ^ "Pitot Static System Performance" (PDF). flighttest.navair.navy.mil. Retrieved on 2008-04-25.
  3. ^ Evans, David. "Safety: Maintenance Snafu with Static Ports". Avionics Magazine. Retrieved on 2008-04-25.
  4. ^ a b c d e f g h "Pitot-Static Instruments - Level 3 - Pitot-Static Instruments". allstar.fiu.edu. Retrieved on 2007-01-07.
  5. ^ a b c "Pilot Handbook - Chapters 6 through 9" (PDF). FAA. Retrieved on 2007-01-07.
  6. ^ a b c d e f g h i j "Flight Instruments - Level 3 - Pitot-Static System and Instruments". allstar.fiu.edu. Retrieved on 2007-01-07.
  7. ^ "ASN Aircraft accident description Boeing 757-225 TC-GEN — Puerto Plata, Dominican Republic". Retrieved on 2007-01-07.
  8. ^ "CVR Database — 2 October 1996 — Aeroperu 603". tailstrike.co. Retrieved on 2007-01-07.
  • Lawford. J. A. and Nippress, K. R. (1983). Calibration of Air-Data Systems and Flow Direction Sensors (AGARD AG-300 - Vol.1, AGARD Flight Test Techniques Series; R. W. Borek, ed.). Accessed via Spaceagecontrol.com (PDF). Retrieved on 25 April 2008.
  • Kjelgaard, Scott O. (1988), Theoretical Derivation and Calibration Technique of a Hemispherical-Tipped Five-Hole Probe (NASA Technical Memorandum 4047).

See also

External links

Tuesday, September 2, 2008

Airspeed indicator

From Wikipedia, the free encyclopedia

Airspeed Indicator in a light single engine aircraft
Airspeed Indicator in a light single engine aircraft

The airspeed indicator or airspeed gauge is an instrument used in an aircraft to display the craft's airspeed, typically in knots, to the pilot.

Markings

A high sensitivity "540 degree" airspeed indicator used in a glider. The pointer swings past zero (top), but the colored arcs do not overlap. The needle shows an indicated airspeed of 60 knots.
A high sensitivity "540 degree" airspeed indicator used in a glider. The pointer swings past zero (top), but the colored arcs do not overlap. The needle shows an indicated airspeed of 60 knots.

Light aircraft

Airspeed indicator markings use a set of standardized colored bands and lines on the face of the instrument. The white range is the normal range of operating speeds for the aircraft with the flaps extended as for landing or takeoff. The green range is the normal range of operating speeds for the aircraft without flaps extended. The yellow range is the range in which the aircraft may be operated in smooth air, and then only with caution to avoid abrupt control movement.

A redline mark indicates VNE, or velocity (never exceed). This is the maximum demonstrated safe airspeed that the aircraft must not exceed under any circumstances. The red line is preceded by a yellow band which is the caution area, which runs from VNO (maximum structural cruise speed) to VNE. A green band runs from VS1 to VNO. VS1 is the stall speed with flaps and landing gear retracted. A white band runs from VSO to VFE. VSO is the minimum steady flight speed with flaps extended, and VFE is the highest speed at which flaps can be extended. Airspeed indicators in multi-engine aircraft show a short radial red line near to the bottom of green arc for Vmc, the minimum indicated airspeed at which the aircraft can be controlled with the critical engine inoperative and a blue line for VYSE, the speed for best rate of climb with the critical engine inoperative.

Airspeed indicator markings for a light multiengine airplane.
Airspeed indicator markings for a light multiengine airplane.

Large aircraft

The airspeed indicator is especially important for monitoring V-Speeds while operating an aircraft. However, in large aircraft, V-speeds can vary considerably depending on airfield elevation, temperature and aircraft weight. For this reason the coloured ranges found on the ASIs of light aircraft are not used - instead the instrument has a number of moveable pointers known as bugs which may be preset by the pilot to indicate appropriate V-speeds for the current conditions.

Jet aircraft do not have VNO and VNE like piston-engined aircraft, but instead have a maximum operating IAS, VMO and maximum Mach number, MMO. To observe both limits, the pilot of a jet airplane needs both an airspeed indicator and a Machmeter, each with appropriate red lines. In some general aviation jet airplanes, the Machmeter is combined into a single instrument that contains a pair of concentric indicators, one for the indicated airspeed and the other for indicated Mach number.

An alternative single instrument is the "maximum allowable airspeed indicator." It has a movable pointer that indicates the never-exceed speed, which changes with altitude to avoid the onset of transonic shock waves on the wing. The pointer is usually red-and-white striped, and thus known as a "barber pole". As the aircraft climbs to high altitude, such that MMO rather than VMO becomes the limiting speed, the barber pole moves to lower IAS values.

Modern aircraft employing glass cockpit instrument systems employ two airspeed indicators: an electronic indicator on the primary flight data panel and a traditional mechanical instrument for use if the electronic panels fail. The airspeed is typically presented in the form of a "tape strip" that moves up and down, with the current airspeed in the middle. The same color scheme is used as on a mechanical airspeed indicator to represent the V speeds.In modern aircraft it even have another electronic indicator airspeed.

Operation

Airspeed indicator connections
Airspeed indicator connections

Along with the altimeter and vertical speed indicator, the airspeed indicator is a member of the pitot-static system of aviation instruments, so named because they operate by measuring pressure in the pitot and static circuits.

Airspeed indicators work by measuring the difference between static pressure, captured through one or more static ports; and stagnation pressure due to "ram air", captured through a pitot tube. This difference in pressure due to ram air is called impact pressure.

Internal mechanism of an airspeed indicator
Internal mechanism of an airspeed indicator

The static ports are located on the exterior of the aircraft, at a location chosen to detect the prevailing atmospheric pressure as accurately as possible, that is, with minimum disturbance from the presence of the aircraft. Some aircraft have static ports on both sides of the fuselage or empennage, in order to more accurately measure static pressure during slips and skids. Aerodynamic slips and skids cause either or both static ports and pitot tube(s) to present themselves to the relative wind in other than basic forward motion. Thus, alternative placement on some aircraft.

Icing is a problem for pitot tubes when the air temperature is below freezing and visible moisture is present in the atmosphere, as when flying through cloud or precipitation. Electrically heated pitot tubes are used to prevent ice forming over the tube.

The airspeed indicator and altimeter will be rendered inoperative by blockage in the static system. To avoid this problem, most aircraft intended for use in instrument meteorological conditions are equipped with an alternate source of static pressure. In unpressurised aircraft, the alternate static source is usually achieved by opening the static pressure system to the air in the cabin. This is less accurate, but is still workable. In pressurised aircraft, the alternate static source is a second set of static ports on the skin of the aircraft, but at a different location to the primary source.

Use

The airspeed indicator is used by the pilot during all phases of flight, from take-off, climb, cruise, descent and landing in order to maintain airspeeds specific to the aircraft type and operating conditions as specified in the Operating Manual.

During instrument flight, the airspeed indicator is used in addition to the Artificial horizon as an instrument of reference for pitch control during climbs, descents and turns.

The airspeed indicator is also used in dead reckoning, where time, speed, and bearing are used for navigation in the absence of aids such as NDBs, VORs or GPS.

Alternatives: Lift Reserve Indicator

Lift Reserve Indicator as installed
Lift Reserve Indicator as installed

The "Lift Reserve Indicator", or LRI, has been proposed as an alternative or backup to the Airspeed Indicator (ASI) during critical stages of flight. This is an elegant device but is rarely found in light aircraft or even transport jets. The conventional Airspeed Indicator is less sensitive and less accurate as airspeed diminishes, thus providing less reliable information to the pilot as the aircraft slows towards the stall. The actual stall speed of an aircraft also varies with flight conditions, particularly changes in gross weight and wing loading during maneuvers. The ASI does not show the pilot directly how the stall is being approached during these maneuvers, whereas the LRI does.

The LRI shows the pilot directly the Potential of Wing Lift (POWL) above the stall at all times and at any airspeed, so it is more descriptive and easier for the pilot to use. The LRI uses dynamic differential pressure and angle of attack to operate. It is very fast acting and extremely accurate at slow airspeeds, thus providing more reliable information to the pilot as airspeed diminishes and become critical.

The LRI uses a three zone, red-white-green display. During flight, the green zone is well above the stall where flight controls are firm, angle of attack is low, and the unused POWL is high. The white zone is near the stall where flight controls soften, angle of attack is high, and the unused POWL is diminished. The top of the red zone defines the beginning of the stall. The severity of stall increases as the needle travels deeper into the red. During the takeoff, the LRI uses dymanic pressure to operate and will not lift the needle above the red zone until enough airspeed energy is available to fly.

The pilot adjusts the instrument to indicate the edge of the red-white zone during minimum airspeed practice at altitude, indicating the aircraft has zero POWL beyond that point. Since the wing will stall at the same angle of attack at any airspeed, once properly adjusted the LRI will indicate the red-white edge anytime the stall is approached. This includes landing stalls, climbing stalls, and accelerated stalls. After adjustment, the black line in the center of the white indicates maximum angle of climb and maximum angle of descent with enough reserve lift for the landing flare. With practice, the pilot can use the LRI to determine the exact moment for liftoff with minimum ground roll and maximum angle of climb combined.

The LRI has been well received by STOL pilots and pilots of experimental or home-built aircraft. The LRI is very useful for short field landings, short field takeoffs, and slow speed maneuvers such as steep turns, steep climbs, and steep descents, and also allows pilots of fast or "slippery" aircraft to land with little or no float very reliably. Since the LRI is so useful at the critical lower end of the flight envelope, most pilots will use the LRI as a complement to the ASI, using the LRI for slow speed work and the ASI for cruising and navigational work.

Types of airspeed measurements

Memory aid: "ICE-T" (iced tea), or Indicated->Calibrated->Equivalent->True

At increased Density Altitude, for the same given indicated airspeed the aircraft's true airspeed (TAS) will be higher, but the same indicated airspeed limits (IAS) apply. Likewise, most efficient cruise speed, total drag, available lift, stall speed, and other aerodynamic information depend on calibrated, not true airspeed. Most aircraft exhibit a small difference between the airspeed actually shown on the instrument (indicated airspeed, or IAS) and the speed the instrument should theoretically show (calibrated airspeed or CAS). This difference, called position error, is mainly due to inaccurate sensing of static pressure. It is usually not possible to find a position for the static ports which, at all angles of attack, accurately senses the atmospheric pressure at the altitude at which the aircraft is flying.

Bernoulli's principle states that total pressure is constant along a streamline. Pitot pressure is equal to total pressure so pitot pressure is constant all around the aircraft and does not suffer position error. (However, pitot pressure can suffer alignment error if the pitot tube is not aligned directly into the oncoming airflow.)

The position of static ports must be selected carefully by an aircraft designer because position error must be small at all speeds within the operating range of the aircraft. A calibration chart specific to the type of aircraft is usually provided.

At high speeds and altitudes, calibrated airspeed must be further corrected for compressibility error to give equivalent airspeed (EAS). Compressibility error arises because the impact pressure will cause the air to compress in the pitot tube. The calibration equation (see calibrated airspeed) accounts for compressibility, but only at standard sea level pressure. At other altitudes compressibility error correction may be obtained from a chart. In practice compressibility error is negligible below about 3,000 m / 10,000 feet and 100 m/s / 200 knots CAS.

The true airspeed can be calculated as a function of equivalent airspeed and local air density, (or temperature and pressure altitude which determine density). Some airspeed indicators incorporate a slide rule mechanism to perform this calculation. Otherwise, it can be performed with a calculator such as the E6B handheld circular slide rule. For a quick approximation of TAS add 2% per 300m / 1000 feet of altitude to IAS (or CAS). e.g. IAS = 52 m/s /100 Knots. At 3000 m / 10,000' Above Sea Level, TAS is 62 m/s / 120 Knots.

See also

Sources

Installing and flying the Lift Reserve Indicator, article and photos by Sam Buchanan http://home.hiwaay.net/~sbuc/journal/liftreserve.htm

This article incorporates text from Airplane Flying Handbook, a public domain work of the United States Government.
This article incorporates text from Instrument Flying Handbook, a public domain work of the United States Government.
This article incorporates text from Pilot's Handbook of Aeronautical Knowledge, a public domain work of the United States Government.

Wednesday, July 16, 2008

Flight instruments

From Wikipedia, the free encyclopedia

Six basic instruments in a light twin-engine airplane arranged in the basic-T. From top left: airspeed indicator, attitude indicator, altimeter, turn coordinator, heading indicator, and vertical speed indicator
Most aircraft are equipped with a standard set of flight instruments which give the pilot information about the aircraft's attitude, airspeed, and altitude.
Most aircraft have these six basic flight instruments:
Altimeter
Gives the aircraft's height (usually in feet or meters) above some reference level (usually sea-level) by measuring the local air pressure. It is adjustable for local barometric pressure (referenced to sea level) which must be set correctly to obtain accurate altitude readings.
Attitude indicator (also known as an artificial horizon)
Shows the aircraft's attitude relative to the horizon. From this the pilot can tell whether the wings are level and if the aircraft nose is pointing above or below the horizon. This is a primary instrument for instrument flight and is also useful in conditions of poor visibility. Pilots are trained to use other instruments in combination should this instrument or its power fail.

The flight instruments of a Slingsby T-67 Firefly two-seat light airplane. The basic T is present on the left side primary pilot station
Airspeed indicator
Shows the aircraft's speed (usually in knots) relative to the surrounding air. It works by measuring the ram-air pressure in the aircraft's pitot tube. The indicated airspeed must be corrected for air density (which varies with altitude, temperature and humidity) in order to obtain the true airspeed, and for wind conditions in order to obtain the speed over the ground.
Magnetic compass
Shows the aircraft's heading relative to magnetic north. While reliable in steady level flight it can give confusing indications when turning, climbing, descending, or accelerating due to the inclination of the earth's magnetic field. For this reason, the heading indicator is also used for aircraft operation. For purposes of navigation it may be necessary to correct the direction indicated (which points to a magnetic pole) in order to obtain direction of true north or south (which points to the earth's axis of rotation).

Schempp-Hirth Janus-C glider Instrument panel equipped for "cloud flying". The turn and bank indicator is top center. The heading indicator is replaced by a GPS-driven computer with wind and glide data, driving two electronic variometer displays to the right.
Heading indicator
Also known as the directional gyro, or DG. Sometimes also called the gyrocompass, though usually not in aviation applications. Displays the aircraft's heading with respect to magnetic north. Principle of operation is a spinning gyroscope, and is therefore subject to drift errors (called precession) which must be periodically corrected by calibrating the instrument to the magnetic compass. In many advanced aircraft (including almost all jet aircraft), the heading indicator is replaced by a Horizontal Situation Indicator (HSI) which provides the same heading information, but also assists with navigation.
Turn and bank indicator, turn coordinator or turn indicator
The turn and bank indicator, also called the turn and slip indicator, displays direction of turn and rate of turn. Internally mounted inclinometer displays 'quality' of turn, i.e. whether the turn is correctly coordinated, as opposed to an uncoordinated turn, wherein the aircraft would be in either a slip or a skid. Replaced in the late sixties and early seventies by the newer turn coordinator, the turn and bank is typically only seen in aircraft manufactured prior to that time, or in Gliders manufactured in Europe.
A turn coordinator displays rate and direction of roll while the aircraft is rolling; displays rate and direction of turn while the aircraft is not rolling. Internally mounted inclinometer also displays quality of turn. Replaced the older turn and bank indicator.
Vertical speed indicator
Also sometimes called a variometer. Senses changing air pressure, and displays that information to the pilot as a rate of climb or descent in feet per minute, meters per second or knots.

Arrangement in instrument panel
Most aircraft built since about 1953 have four of the flight instruments located in a standardized pattern called the T arrangement. The attitude indicator is in the top center, airspeed to the left, altitude to the right and heading indicator under the attitude indicator. The other two, turn-coordinator and vertical-speed, are usually found under the airspeed and altitude, but are given more latitude in placement. The magnetic compass will be above the instrument panel, often on the windscreen centerpost. In newer aircraft with glass cockpit instruments the layout of the displays conform to the basic T arrangement.


See also
Glass cockpit

[edit] External links
Instrument Flying Handbook (FAA-H-8083-15A) 2007
The Gyro Horizon Enables Instrument Flying A history of how aircraft instrumentation was developed with an emphasis on the gyro horizon. (c) 2007


v • d • eFlight instruments
Pitot-static instruments: Altimeter · Airspeed indicator · Machmeter · Variometer
Gyroscopic instruments: Attitude indicator · Heading indicator · Horizontal situation indicator · Turn and bank indicator · Turn coordinator · Turn indicator
Navigation: Horizontal situation indicator · Course Deviation Indicator · Inertial navigation system · GPS · SIGI ·


v • d • eSatellite navigation systems

Historical
Transit (USA)

Operational
GLONASS (USSR/Russia) · GPS (USA) · Beidou (China)

Developmental
COMPASS (China) · Galileo (Europe) · IRNSS (India) · QZSS (Japan)

GNSS augmentation systems
EGNOS · GAGAN · GPS·C · LAAS · MSAS · WAAS · StarFire

Related topics
GNSS · GNSS reflectometry · Kalman filter

Other: Magnetic compass · Yaw string · Glass cockpit · EFIS

Retrieved from "http://en.wikipedia.org/wiki/Flight_instruments"

Categories: Aircraft instruments Aviation Display technology Measuring instruments Navigation Navigational equipment


This page was last modified on 1 July 2008, at 00:31.
All text is available under the terms of the GNU Free Documentation License. (See Copyrights for details.) Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a U.S. registered 501(c)(3) tax-deductible nonprofit charity.
Privacy policy
About Wikipedia
Disclaimers