Showing posts with label aeronautical chart. Show all posts
Showing posts with label aeronautical chart. Show all posts

Friday, November 7, 2008

Aeronautical chart

From Wikipedia, the free encyclopedia

An aeronautical chart is a map designed to assist in navigation of aircraft, much as nautical charts do for watercraft, or a roadmap for drivers. Using these charts and other tools pilots are able to determine their position, safe altitude, best route to a destination, navigation aids along the way, alternative landing areas in case of an in-flight emergency, and other useful information such as radio frequencies and airspace boundaries. There are charts for all land masses on Earth, and long-distance charts for trans-oceanic travel.

Specific charts are used for each phase of a flight and may vary from a map of a particular airport facility to an overview of the instrument routes covering an entire continent (e.g., global navigation charts), and many types in between.

Charts for visual flight rules (VFR)

Under "visual flight rules", pilots are expected to see and avoid dangers along the way (obstacles, other aircraft, bad weather, etc), and to use pilotage and other means for navigating. VFR charts include a large amount of information describing the local topography, not the least of which is the elevation. Standardized symbols are used for indication of land and water features such as mountains, shorelines and rivers. Roads, towns and other identifiable features may also be shown, in addition to specific aeronautical details.

Visual flight charts are divided into categories, depending upon their scale, which is proportional to the size of the area covered by one map. The amount of detail is necessarily reduced when larger areas are covered with a map having a compact scale.

  • World aeronautical charts (WACs) have a scale of 1:1,000,000 and cover relatively large areas. Outside of WAC coverage, operational navigation charts (ONC) may be used, having the same scale as WACs.
  • Sectional charts typically cover a few hundred square miles of area (1:500,000).
  • VFR Terminal area charts are created with a scale and coverage appropriate for the general vicinity of a large airport (1:250,000). They may depict preferred VFR flight routes within areas of congested airspace.

Charts for instrument flight rules (IFR)

Instrument flight requires the use of artificial aids to navigation, under the control of an air traffic controller, usually based upon a flight plan. The charts used for IFR flights contain an abundance of information regarding locations (waypoints) "fix" according to measurements from electronic beacons of various types, as well as the routes connecting these waypoints. Only limited topographic information is found on IFR charts.

En-route low and high altitude charts are published with a scale that depends upon the density of navigation information required in the vicinity.

Information from IFR charts is often programmed into an flight management system or autopilot system, which may simplify many of the tasks involved in following (or deviating from) a flight plan.

Terminal procedure publications such as Standard Terminal Arrival plates, Standard Instrument Departure plates, and other documentation provide detailed information for arrival, departure and taxiing at each approved airport having instrument capabilities of some sort.

Sources for charts

Aeronautical charts may be purchased at fixed base operators (FBOs), internet supply sources, or catalogs of aeronautical gear. They may also be viewed online from sources such as Skyvector and the FAA.

See also

Thursday, August 28, 2008

Pilotage

From Wikipedia, the free encyclopedia

Pilotage is the use of fixed visual references on the ground or sea by means of sight or radar to guide oneself to a destination, sometimes with the help of a map or nautical chart. People use pilotage for activities such as guiding vessels and aircraft, hiking and Scuba diving. When visual references are not available, it is necessary to use an alternative method of navigation such as dead reckoning (typically with a compass), radio navigation, and satellite navigation (such as GPS).

Difficulties
Pilotage depends on the pilot being able to recognise the visual references in order to make use of them. The pilot must either be familiar with those visual references or be able to discover them from a map, aeronautical chart or nautical chart. Many nautical and aeronautical disasters have resulted from the pilot incorrectly identifying visual references.
Poor visibility may affect safe navigation by obscuring the natural features used by pilots in an area. In such situations, pilots use navigational aids such as radar and the GPS to determine position and monitor their passage.

Visual features
Common types of visual reference point used for pilotage:
During the day:
Natural features: Mountains, hills, lakes, rivers and coastal features such as cliffs, rocks and beaches
Man made nautical features: sea marks, land marks and radio aerials
Man made land features: Airports, cities, dams and highways
At night:
Man made nautical features: Lighthouses, lightships and sea marks with lights
Man made land features: Airports, illuminated towers and buildings
Pilotage is frequently combined with navigation techniques such as dead reckoning. When a pilot at a known location cannot see the next visual reference on the route to a destination, he or she can use dead reckoning to get closer to the next reference point. This is the most common form of VFR navigation.

See also
Maritime pilot
American Practical Navigator

Wednesday, July 16, 2008

Air Navigation

From Wikipedia, the free encyclopedia
The principles of air navigation are the same for all aircraft, big or small. Air navigation involves successfully piloting an aircraft from place to place without getting lost, breaking the laws applying to aircraft, or endangering the safety of those on board or on the ground.
Air navigation differs from the navigation of surface craft in several ways:
Aircraft travel at relatively high speeds, leaving less time to calculate their position en route. Aircraft normally cannot stop in mid-air to ascertain their position at leisure. Aircraft are safety-limited by the amount of fuel they can carry; a surface vehicle can usually get lost, run out of fuel, then simply await rescue. There is no in-flight rescue for most aircraft. And collisions with obstructions are usually fatal. Therefore, constant awareness of position is critical for aircraft pilots.
The techniques used for navigation in the air will depend on whether the aircraft is flying under the visual flight rules (VFR) or the instrument flight rules (IFR). In the latter case, the pilot will navigate exclusively using instruments and radio navigation aids such as beacons, or as directed under radar control by air traffic control. In the VFR case, a pilot will largely navigate using dead reckoning combined with visual observations (known as pilotage), with reference to appropriate maps. This may be supplemented using radio navigation aids.


Route planning
The first step in navigation is deciding where one wishes to go. A private pilot planning a flight under VFR will usually use an aeronautical chart of the area which is published specifically for the use of pilots. This map will depict controlled airspace, radio navigation aids and airfields prominently, as well as hazards to flying such as mountains, tall radio masts, etc. It also includes sufficient ground detail - towns, roads, wooded areas - to aid visual navigation. In the UK, the CAA publishes a series of maps covering the whole of the UK at various scales, updated annually. The information is also updated in the notices to airmen, or NOTAMs.
The pilot will choose a route, taking care to avoid controlled airspace that is not permitted for the flight, restricted areas, danger areas and so on. The chosen route is plotted on the map, and the lines drawn are called the track. The aim of all subsequent navigation is to follow the chosen track as accurately as possible. Occasionally, the pilot may elect on one leg to follow a clearly visible feature on the ground such as a railway track, river, highway, or coast.

Adjustment of an aircraft's heading to compensate for wind flow perpendicular to the ground track
When an aircraft is in flight, it is moving relative to the body of air it is flying in, therefore maintaining an accurate ground track is not as easy as it might appear, unless there is no wind at all — a very rare occurrence. Therefore the pilot must adjust heading to compensate for the wind, in order to follow the ground track. Initially the pilot will calculate headings to fly for each leg of the trip prior to departure, using the forecast wind directions and speeds supplied by the meteorological authorities for the purpose. These figures are generally accurate and updated several times per day, but the unpredictable nature of the weather means that the pilot must be prepared to make further adjustments in flight. A general aviation (GA) pilot will often make use of either the E6B flight computer - a type of slide rule - or a purpose designed electronic navigational computer to calculate initial headings.
The primary instrument of navigation is the magnetic compass. The needle or card aligns itself to magnetic north, which does not coincide with true north, so the pilot must also allow for this, called the magnetic variation (or declination). The variation that applies locally is also shown on the flight map. Once the pilot has calculated the actual headings required, the next step is to calculate the flight times for each leg. This is necessary to perform accurate dead reckoning. The pilot also needs to take into account the slower initial airspeed during climb to calculate the time to top of climb. It is also helpful to calculate the top of descent, or the point at which the pilot would plan to commence the descent for landing.
The flight time will depend on both the desired cruising speed of the aircraft, and the wind - a tailwind will shorten flight times, a headwind will increase them. The E6B has scales to help pilots compute these easily.
The point of no return is the point on a flight at which a plane has just enough fuel, plus any mandatory reserve, to return to the airfield from which it departed. Beyond this point that option is closed, and the plane must proceed to some other destination.
Alternatively, with respect to a large region without airfields, e.g. an ocean, it can mean the point before which it is closer to turn around and after which it is closer to continue.
Additional calculations depending on the aircraft and the terrain may include single engine flight characteristics in the event of a loss of one of a twin's engines in flight.
The final stage is to note over which areas the route will go, and to make a note of all of the things to be done - which ATC units to contact, the appropriate frequencies, visual reporting points, and so on. It is also important to note which pressure setting regions will be entered, so that the pilot can ask for the QNH (air pressure) of those regions. Finally, the pilot should have in mind some alternative plans in case the route cannot be flown for some reason - unexpected weather conditions being the most common. At times the pilot may be required to file a flight plan for an alternate destination and to carry adequate fuel for this. The more work a pilot can do on the ground prior to departure, the easier it will be in the air.

IFR planning
In many respects this is similar to VFR flight planning except that the task is generally made simpler by the use of special charts that show IFR routes from beacon to beacon with the lowest safe altitude (LSALT), bearings (in both directions) and distance marked for each route. IFR pilots may fly on other routes but they then have to do all of these calculations themselves with the LSALT calculation being the most difficult. The pilot then needs to look at the weather and minimum specifications for landing at the destination airport and the alternate requirements. The pilot must also comply with all the rules including their legal ability to use a particular instrument approach depending on how recently they last performed one.

In flight
Once in flight, the pilot must take pains to stick to plan, otherwise getting lost is all too easy. This is especially true if flying over featureless terrain. This means that the pilot must stick to the calculated headings, heights and speeds as accurately as possible. The visual pilot must regularly compare the ground with the map, (pilotage) to ensure that the track is being followed although adjustments are generally calculated and planned. Usually, the pilot will fly for some time as planned to a point where features on the ground are easily recognised. If the wind is different from that expected, the pilot must adjust heading accordingly, but this is not done by guesswork, but by mental calculation - often using the 1 in 60 rule. For example a two degree error at the halfway stage can be corrected by adjusting heading by four degrees the other way to arrive in position at the end of the leg. This is also a point to reassess the estimated time for the leg. A good pilot will become adept at applying a variety of techniques to stay on track.
While the compass is the primary instrument used to determine one's heading, pilots will usually refer instead to the direction indicator (DI), a gyroscopically driven device which is much more stable than a compass. The compass reading will be used to correct for any drift (precession) of the DI periodically. The compass itself will only show a steady reading when the aircraft has been in straight and level flight long enough to allow it to settle.
Should the pilot be unable to complete a leg - for example bad weather arises, or the visibility falls below the minima permitted by the pilot's license, the pilot must divert to another route. Since this is an unplanned leg, the pilot must be able to mentally calculate suitable headings to give the desired new track. Using the E6B in flight is usually impractical, so mental techniques to give rough and ready results are used. The wind is usually allowed for by assuming that sine A = A, for angles less than 60° (when expressed in terms of a fraction of 60° - e.g. 30° is 1/2 of 60°, and sine 30° = 0.5), which is adequately accurate. A method for computing this mentally is the clock code. However the pilot must be extra vigilant when flying diversions to maintain awareness of position.
Some diversions can be temporary - for example to skirt around a local storm cloud. In such cases, the pilot can turn 60 degrees away his desired heading for a given period of time. Once clear of the storm, he can then turn back in the opposite direction 120 degrees, and fly this heading for the same length of time. This is a 'wind-star' maneuver and, with no winds aloft, will place him back on his original track with his trip tme increased by the length of one diversion leg.

Navigation Aids
Main article: Radio navigation


Good pilots use all means available to help navigate. Many GA aircraft are fitted with a variety of radio navigation aids, such as Automatic direction finder (ADF), VHF omnidirectional range (VOR) and Global Positioning System (GPS).
ADF uses non-directional beacons (NDBs) on the ground to drive a display which shows the direction of the beacon from the aircraft. The pilot may use this bearing to draw a line on the map to show the bearing from the beacon. By using a second beacon, two lines may be drawn to locate the aircraft at the intersection of the lines. This is called a cross-cut. Alternatively, if the track takes the flight directly overhead a beacon, the pilot can use the ADF instrument to maintain heading relative to the beacon, though "following the needle" is bad practice, especially in the presence of a strong cross wind - the pilot's actual track will spiral in towards the beacon, not what was intended. NDBs also can give erroneous readings because they use very long wavelengths, which are easily bent and reflected by ground features and the atmosphere. NDBs continue to be used as a common form of navigation in some countries with relatively few navigational aids.
VOR is a more sophisticated system, and is still the primary air navigation system established for aircraft flying under IFR in those countries with many navigational aids. In this system, a beacon emits a specially modulated signal which consists of two sine waves which are out of phase. The phase difference corresponds to the actual bearing relative to true north that the receiver is from the station. The upshot is that the receiver can determine with certainty the exact bearing from the station. Again, a cross-cut is used to pinpoint the location. Many VOR stations also have additional equipment called DME (distance measuring equipment) which will allow a suitable receiver to determine the exact distance from the station. Together with the bearing, this allows an exact position to be determined from a single beacon alone. For convenience, some VOR stations also transmit local weather information which the pilot can listen in to, perhaps generated by an Automated Surface Observing System.
Prior to the advent of GPS, Celestial Navigation was also used by trained navigators on military bombers and transport aircraft in the event of all electronic navigational aids being turned off in time of war. Originally navigators used an astrodome and regular sextant but the more streamlined periscopic sextant was used from the 1940s to the 1990s.
Finally, an aircraft may be supervised from the ground using radar. ATC can then feed back information to the pilot to help establish position, or can actually tell the pilot the position of the aircraft, depending on the level of ATC service the pilot is receiving.
The use of GPS navigation in aircraft is becoming increasingly common. GPS provides very precise aircraft position, altitude, heading and ground speed information. GPS makes navigation precision once reserved to large RNAV-equipped aircraft available to the GA (general aviation) pilot. Recently, more and more airports include GPS instrument approaches. GPS approaches consist of either overlays to existing non-precision approaches or stand-alone GPS non-precision approaches.

See also
ADS-B
Aeronautical chart
Air safety
RAIM
Great-circle distance
ETOPS/LROPS
Flight instruments
Flight management system
Flight planning
Instrument Landing System
Air traffic obstacle
Radio navigation
SIGI
Spherical trig
transatlantic flight
Wind triangle

External links
Fly Away - Air Navigation tutorials
v • d • eSatellite navigation systems
Historical
Transit (USA)
Operational
GLONASS (USSR/Russia) · GPS (USA) · Beidou (China)
Developmental
COMPASS (China) · Galileo (Europe) · IRNSS (India) · QZSS (Japan)
GNSS augmentation systems
EGNOS · GAGAN · GPS·C · LAAS · MSAS · WAAS · StarFire
Related topics
GNSS · GNSS reflectometry · Kalman filter

v • d • eFlight instruments
Pitot-static instruments: Altimeter · Airspeed indicator · Machmeter · Variometer
Gyroscopic instruments: Attitude indicator · Heading indicator · Horizontal situation indicator · Turn and bank indicator · Turn coordinator · Turn indicator
Navigation: Horizontal situation indicator · Course Deviation Indicator · Inertial navigation system · GPS · SIGI ·

v • d • eSatellite navigation systems
Historical
Transit (USA)
Operational
GLONASS (USSR/Russia) · GPS (USA) · Beidou (China)
Developmental
COMPASS (China) · Galileo (Europe) · IRNSS (India) · QZSS (Japan)
GNSS augmentation systems
EGNOS · GAGAN · GPS·C · LAAS · MSAS · WAAS · StarFire
Related topics
GNSS · GNSS reflectometry · Kalman filter
Other: Magnetic compass · Yaw string · Glass cockpit · EFIS
Retrieved from "http://en.wikipedia.org/wiki/Air_navigation"
Categories: Navigation Air traffic control

All text is available under the terms of the GNU Free Documentation License. (See Copyrights for details.) Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a U.S. registered 501(c)(3) tax-deductible nonprofit charity.
Privacy policy
About Wikipedia
Disclaimers